| You can continuously measure and regulate the pH-value of your aquarium with the help of this module. As the module is galvanically seperated from the basic system, the pH-value can also be measured at different points within a single water circuit without the individual sensors having an effect on each other.
| |
|
| iks conductivity module for the IKS aquastar system. For the se in fresh and seawater.
| |
|
| You can fully automatically ensure a constant water level in your aquarium using the water-level module (automatic level system). To float switch used is installed inside a casing protected from waves to prevent a pump switching on and off unnecessarily. In the unlikely event of the float switch failing, a timed alarm can be triggered to prevent flooding your living room.
| |
|
| You can use the air-pressure module to measure the absolute air pressure. Please note that it is the relative air pressure that given in, for example, weather reports or other media. The relative air pressure always refers to sea-level.
| |
|
| You can continuously measure and regulate the redox potential of your aquarium with the help of these module. As the module is galvanically separated from the basic system, the redox potential can also be measured at different points within a single water circuit without the individual sensors having an effect on each other. You can choose between having the redox potential displayed on the iks aquastar im mV or as the rH-value.
| |
|
| Using the oxygen module, the IKS aquastar can continuously measure and regulate the oxygen content in your fresh and seawater aquarium. And while it is doing so, you can have the oxygen content displayed in mg/l or the oxygen saturation in %. As the module is galvanically separated from the basic system, the oxygen content can be measured at different points in a water circuit without the individual sensors having an effect on each other.
| |
|
| The temperature cab be precisely and continuously measured and controlled in your aquarium with these temperature module. You can stipulate a variety of settings for day and night, and for summer and winter, too. You van reproduce natural changes in temperature in your aquarium.
| |
|
| This 4-channel module allows the multitude of simulations of light and current that the IKS aquastar and iks aquastar midi systems provide to be used to their greatest effect. All you require to be able to dim fluorescent tubes are electronically dimmable ballast units (ECG e.g. Osram (Quicktronic®) , Philips (HF-Regulator) etc.).But current pumps with an output of up to several kilowatts can be controlled by means of this module and so-called frequency converters.
| |
|
| By connecting this controller to the iks aquastar and iks aquastar midi systems, the readings can be sent to a mobile phone anywhere in the world by SMS. If a reading exceeds certain limits (alarm), the module automatically sends an SMS. In other words: you receive timely notification that enables you to take steps to prevent what could otherwise be worse damage.
| |
|
| Up to four switch sockets can be connected to the IKS aquastar system, each with four switch sockets. You can therefore individually control a total of 16 sockets.
| |
|
| IKS Aquaview is a external control panel with touch display for the IKS aquastar and Pondpilot computers. The polished front glass has the look of a high-quality tablet and without too much supporting information, appears to allow for full access to the Aquastar controller to monitor and control lighting, parameters and other equipment.
| |
|
| IKS pH electrode with BNC connector for the IKS aquaristic computers aquastar or any other pH system with BNC connector. Very high quality and long life.
| |
|
| Technical data:black polysulfone shaftShaft lenght: 120 mmShaft diameter: 12 mmDiaphragm: CeramicElectrolyte: GelTemperatre range: 0..80 °CCable: 2 m low-interference, coaxial cableConnection: BNC plugPlatin cap diameter: 6 mm.
| |
|
| Technical data:Cable: 3 m long, black supply lineSensor element: Pt1000 Class AConnection: BNC plug.
| |
|
| With this sensor holder, you can attach up to 6 sensors to your aquarium.The holder is suitable for vertical as well as horizontal fitting. For wall-thickness up to 16 mm.
| |
|
| How accurate a measurement is depends, among other factors, greatly on the calibration. Precondition for good calibration is precision calibration-solution. Available as pH 4, pH 7 or pH 9, with 50 ml content/each.
| |
|
| IKS BNC - cable for the connection of the IKS electrodes. Available in lenghts with: 2.0 m and 5.0 m.
| |
|
| IKS data cable for switch socket cable as extension, available in 2 m, 5 m and 10 m lenght.
| |
|